Everything you need to measure, assemble and install made-to-measure fly screens yourself. We cut your aluminium fly screen frame and mesh to the exact size you order and send it flat-packed, ready to build at home.
Safety first: fly screens keep insects out. They are not safety barriers and won't stop a child falling through a window. Read our safety information.
Please read through this guide before you order. Fly Screens In a Box cuts your aluminium frame and fly screen mesh to the exact size you enter, and supplies the parts you need to assemble each screen at home.
Enter your size, then pick your frame colour and mesh type in our fly screen builder.
Your flat-pack kit arrives cut to size. Most screens take 10–20 minutes to build.
Every window is different, so work out whether your screen will be face fit, loose fit or track fit before you measure. Our installation guide explains each method. Fly Screens In a Box is designed as an easy DIY solution for standard windows. If you can't see an easy way to fix a screen to your window, it's probably time to call a professional installer.
We don't add or take away anything from your measurements. We cut exactly to the size you enter. Always measure carefully and double-check your numbers before ordering. Fly Screens In a Box can't be responsible for incorrectly measured fly screens.
Most Australian windows take 11 mm. Bradnam's and A&L windows usually need 9 mm. Check your frame size
Larger screens need a colour-matched mid rail for strength. About mid rails
Your screen needs to sit above the winder. See our awning window tip
Re-mesh your existing frame with our fly screen mesh cut to size, then follow the mesh fitting steps.
Every kit is cut to your measurements and packed ready to assemble. Each fly screen comes with:
A spline roller makes rolling the spline in much easier and stops you piercing the mesh. We strongly recommend using one.
Need a spare part? We sell corner stakes, spline, replacement fly frame pieces and all our fixings separately. See all fly screen parts and accessories.
Accurate measurements are the key to a fly screen that fits perfectly. We cut every frame and mesh to exactly the size you enter. We don't add or deduct anything, so the numbers you give us are the size of your finished screen.
Measure in millimetres with a metal tape. Measure each side in three places and use the smallest number. Write W (width) or H (height) next to every measurement so they don't get mixed up.
If your old screen fitted well, just measure it. Measure the width and height at both ends and in the centre and order the smallest of each. Some old screens bow in the middle. Don't measure across a bowed section, as it will make your new screen too short.
Most Australian windows take the standard 11 mm fly screen frame. Some brands, such as Bradnam's and A&L, have narrower channels and need the slimmer 9 mm frame. If your screen will sit in a track or channel, measure how wide it is.
The Australian standard. Choose 11 mm if the channel your screen sits in is wider than 11 mm.
For channels less than 11 mm wide, common on Bradnam's and A&L windows. Our top track, bottom track and chain winder adaptor don't fit 9 mm frames.
There are three ways to mount a fly screen, and each is measured a little differently.
| Mount type | Where it sits | Fixings | Order size |
|---|---|---|---|
| Face fit | On the flat face of the window frame or architrave | Swivel clips or flat swivel clips | Opening + 40 mm |
| Loose fit | Inside a recess with no tracks | Plunger pins | Opening − 2 mm |
| Track fit | In the window's top and bottom tracks (most sliding windows) | None needed | Opening + track depth − 3 mm |
The screen sits flat against the window frame or architrave and overlaps the opening. You need at least 20 mm of flat surface all the way around.
Inside edge to inside edge of the opening, at the top, middle and bottom. Use the smallest.
Top to bottom of the opening, at the left, centre and right. Use the smallest.
This gives a 20 mm overlap on every side.
Example: CW 800 mm × CH 1000 mm → order 840 mm (W) × 1040 mm (H).
Fixings: swivel clips screw into the window frame and turn over the edge of the screen. Flat swivel clips screw onto the fly screen frame and hook behind the window frame, which is handy when you can't screw into the window. Narrow rebate? Use 9 mm swivel clips.
The screen sits inside a recessed window frame that has no tracks, held in place with plunger pins.
Inner face to inner face inside the recess, at the top, middle and bottom. Use the smallest.
From the underside of the top reveal to the top of the sill lip, at the left, centre and right. Use the smallest.
This leaves just enough room for the screen to fit easily.
Example: CW 785 mm × CH 1024 mm → order 783 mm (W) × 1022 mm (H).
Fixings: plunger pins fit into holes drilled in the screen frame and the recess. They lock the screen in place but still let you pop it out for cleaning.
Most common on aluminium sliding windows. The screen lifts up into the top track and drops into the bottom track, so it's actually bigger than the opening you can see.
Between the inside faces of the left and right tracks, at the top, middle and bottom. Use the smallest.
From the top of the bottom track lip to the underside of the top track lip, at the left, centre and right. Use the smallest.
Measure the depth of the top and bottom tracks and record the larger one as TDH (usually the top track). Do the same for the side tracks and record the larger one as TDW.
The 3 mm gives you the clearance to lift the screen in and out.
Example: CW 865, CH 1048, TDW 8, TDH 10 → order 870 mm (W) × 1055 mm (H).
Fixings: none needed. The tracks hold the screen. No tracks on your window? Add a fly screen top track and bottom track to create your own. These tracks suit 11 mm frames only.
| Mount type | Where to measure | Formula | Fixings |
|---|---|---|---|
| Face fit | Clear opening on the face of the frame | W = CW + 40 mm H = CH + 40 mm | Swivel clips / flat swivel clips |
| Loose fit | Inside the recess, inner edge to inner edge | W = CW − 2 mm H = CH − 2 mm | Plunger pins |
| Track fit | Inside the tracks, lip to lip | W = CW + TDW − 3 mm H = CH + TDH − 3 mm | None |
Your DIY fly screen kit arrives pre-cut and ready to put together. Watch the video or follow the steps below. Most screens take 10–20 minutes.
Prefer YouTube? Watch on YouTube · More how-to videos
Check the frame lengths match your order before you start.
A rubber mallet or nylon hammer, a tape measure, a sharp utility knife and a flat, clean work surface.
Place the four frame pieces flat on your work surface with the spline groove facing up. This groove is where the mesh and spline lock in later.
Push a corner stake into the end of one frame piece, then push the next piece onto it. Tap the mitred corner together with your mallet. Join three sides this way, then put the last two corner stakes into both ends of the final piece and close up the frame.
Measure both diagonals, corner to corner. They should be the same. If they're not, gently push the frame by hand until they are. Work on a flat surface, because even a slight twist affects the mesh tension.
Fit your mid rail after the frame is together and before the mesh goes on. Follow our mid rail steps, then come back to Step 4.
Lay the mesh over the frame with the weave square to the edges and a little overhang on every side.
Starting at a corner, use the wheel of the spline roller to press the spline and mesh into the groove. Use the heel of the roller to push the spline right into the corners.
Roll along each side, holding the mesh with your free hand so it stays square. Roll the D-ring pull tab in under the spline on the edge you'll lift the screen from.
On the last side, gently pull the mesh as you roll the spline in so it ends up firm and wrinkle-free. Not happy with it? Pull the spline out and try again.
Angle a sharp utility knife slightly inward and cut the mesh just above the spline, inside the groove, for a clean edge.
Metal mesh is stiffer, so the method changes slightly. Before rolling in the spline, gently crease the mesh into the groove with the roller wheel. This stops it tearing. Then roll the spline in with firm, steady pressure and take your time.
That's it. Your fly screen is ready to install.
A mid rail is a colour-matched aluminium bar that runs across (or down) the middle of a larger fly screen. It strengthens the frame, stops it bowing and gives big screens a neater finish.
Recommended for larger screens and required for screens over 1200 mm × 1200 mm.
Choose the direction in step 4 of the fly screen builder and we'll cut it to suit your screen.
Every mid rail matches your frame colour and comes with 2 mid rail joiners (clips), one for each end.
The mid rail isn't fixed until the spline is rolled over the lip of each joiner.
Push one mid rail joiner into each end of the mid rail. Make sure both are fully inserted and sitting straight.
Place your assembled frame on a flat surface with the spline groove facing up.
Decide where the rail will sit (usually the middle of the screen). Measure down from the top (or up from the bottom) on both sides and mark the same distance so the rail sits level.
Hold the rail above the frame and line up each joiner with the spline groove on the side frames. Lower it in so the joiners sit inside the spline groove and the lip on each joiner hooks under the outer edge of the groove. Press it gently into position. At this point the rail is located, but not locked.
Measure again on both sides and adjust if needed. This is what gives you a clean, professional-looking finish.
Lay the mesh over the frame and use the spline roller to roll the mesh and spline over the lip of each joiner. This locks the joiners into the groove and holds the rail firmly. Then finish fitting the mesh as normal (Assembly Step 4).
Fit the mid rail before you trim the excess mesh. If it needs adjusting, pull the spline back a little, move the rail and roll the spline in again. A straight edge helps you check the rail is level.
If you add a mid rail in the fly screen builder, we work out the length for you. If you're ordering a mid rail on its own, take this off your finished screen size:
| Frame size | Horizontal mid rail | Vertical mid rail |
|---|---|---|
| 11 mm frame | Screen width − 49 mm | Screen height − 49 mm |
| 9 mm frame | Screen width − 43 mm | Screen height − 43 mm |
Example: a 1000 mm wide screen with a horizontal mid rail needs a 951 mm rail on an 11 mm frame (1000 − 49) or a 957 mm rail on a 9 mm frame (1000 − 43).
Once your fly screen is assembled, it's time to fit it to the window. Follow the steps for the mounting method you chose when you measured.
The most common method for flat window frames. The screen sits flat against the front of the window frame or architrave.
You'll need: swivel clips or flat swivel clips (screws included), a drill or screwdriver, a pencil and a tape measure.
Hold the screen against the window frame so it sits level and evenly covers the opening, with no gaps around the edge.
Mark where each clip will go, about 100 mm in from each corner and evenly spaced along the sides. On wider screens, use two clips along the bottom edge.
Screw the clips in so they can still turn freely. Flat swivel clips screw onto the fly screen frame instead and hook behind the window frame.
Put the screen back in position and turn the clips over its edge to hold it.
Mark, fit and turn the top clips to lock the screen in.
The screen should sit tight and flat with no gaps. Don't overtighten the screws.
For recessed window frames with no tracks. It gives a clean finish and lets you remove the screen easily for cleaning.
You'll need: plunger pins, a drill with 4 mm and 6 mm bits, a pencil and a tape measure.
Hold the screen inside the recess and check it sits neatly and evenly, and that the recess is deep enough for your 9 mm or 11 mm frame.
Mark two points on each side of the fly screen frame, about 50–75 mm in from the corners.
Drill 4 mm holes through the fly screen frame at your marks.
Hold the screen in place and use the holes as a guide to mark the recess. Drill 6 mm holes about 6 mm deep at those marks.
Push the pins into the holes in the screen frame. Squeeze them in, line them up with the holes in the window frame and press the screen into place. The pins spring out and lock it in.
The screen should be snug but removable. To take it out, press the pins in and gently pull the screen out.
Tip: a little silicone spray on the plunger pins helps them slide smoothly if you remove the screen often.
Common on aluminium sliding windows. No screws or clips needed, as the tracks hold the screen.
You'll need: nothing. Some thin foam tape or felt strip is handy if the screen rattles.
Hold it parallel to the window with the top edge ready to go into the top track.
Lift the screen so the top edge slides as far up into the top track as it will go.
Swing the bottom edge in over the bottom track lip and lower the screen into the bottom track.
The frame should sit evenly in both tracks without binding.
If the screen rattles, add thin foam tape or felt strip along the frame edges for a snug, quiet fit.
Put one top corner into the top track and the matching side corner into the side track, about two-thirds of the way along. Gently rotate and lift the screen so both corners travel along their tracks until it pops into position, then use the pull tab to even it up. To remove it, push the screen as high as it will go into the top track and into the deeper side track, which frees one corner.
To remove a track-fit screen: lift it up into the top track, tilt the bottom edge out until it clears the bottom track lip, and lower it gently.
No tracks on your window? Fit our top track and bottom track to create a fixed channel for your screen. These tracks suit 11 mm frames only.
| Fixing | What it does |
|---|---|
| Hang tabs | Hook over the window frame. Common on Trend windows. Fitted with rivets. |
| Lift tab plunger | Replaces the D-ring, locks over the track and stops rattles. Fitted with rivets. |
| Plunger tab | Fits the side of the frame and slides out to grip the window frame. |
| Tensioner spring | Flat steel spring that slides into the top corner of the frame. No tools needed. |
| Rivets | Colour-matched rivets for fitting hang tabs and lift tabs. |
We stock five types of fly screen mesh. Choose one in our DIY kits, or buy any of them cut to size to re-mesh an existing frame.
Lightweight, flexible and durable. It won't rust or dent, gives good airflow and visibility, and is the best all-rounder for most homes.
DIY level: beginner. Shop fibreglass mesh
A finer weave that keeps out midges, sandflies and mosquitoes. Ideal for coastal and tropical areas. Airflow and visibility are slightly lower.
DIY level: beginner. Shop midge mesh
Heavy-duty and tear-resistant. Stands up to claws, paws and knocks while still letting the air through.
DIY level: intermediate. Shop pet mesh
Strong, rust-resistant and UV-stable, so it won't fade or weaken. Suitable up to BAL-29. It's firmer to install and can dent if knocked.
DIY level: intermediate. Shop aluminium mesh
Ember-resistant 304 stainless steel, rated to BAL-40. Our strongest mesh, and pet-resistant too. Not suitable for Flame Zone (BAL-FZ).
DIY level: experienced. Shop bushfire mesh
See and feel the mesh before you order. Pick any 3 mesh types for $5. Each pack includes our business card with 10% off your fly screen order.
Australian Standard AS 3959 requires homes in bushfire-prone areas to screen windows and doors with mesh suited to their level of risk. Each site's risk is given a BAL (Bushfire Attack Level) rating, from BAL-LOW (very low risk) to BAL-FZ (Flame Zone). Get your BAL rating from your local council or fire authority, then use the table below.
| Mesh type | BAL-LOW | BAL-12.5 | BAL-19 | BAL-29 | BAL-40 | BAL-FZ |
|---|---|---|---|---|---|---|
| Fibreglass | ✓ | – | – | – | – | – |
| Midge | ✓ | – | – | – | – | – |
| Pet | ✓ | – | – | – | – | – |
| Aluminium | ✓ | ✓ | ✓ | ✓ | – | – |
| 304 stainless steel (bushfire) | ✓ | ✓ | ✓ | ✓ | ✓ | – |
Bushfire regulations and fall prevention are part of the Australian Standards and are mandatory. Everything else in this guide is a recommendation only.
| Mesh | Skill level | What to expect |
|---|---|---|
| Fibreglass | Beginner | Soft and flexible, so it's easy to spline in. Perfect for first-timers. |
| Midge | Beginner | Just as easy as fibreglass. Take a little extra care to keep the fine weave straight. |
| Pet | Intermediate | Thicker and tougher, so it needs firmer rolling pressure. |
| Aluminium | Intermediate | Stiffer and less forgiving. Take care not to crease or kink it. |
| Bushfire (stainless) | Experienced | Strong and rigid. Needs careful cutting and tensioning. |
Our aluminium fly screen frames come in 23 colours, including Surf Mist, Monument, Woodland Grey and Black. Try them in our colour visualiser or order a frame colour sample pack.
Frames are cut each week. Order before Thursday 10 am and your frames arrive at our Miranda workshop the following Monday. We then pack and dispatch your kit that week, and courier delivery usually takes 3–5 business days. Allow 2 weeks from order to delivery. See Shipping for the full schedule.
Yes. Everything comes cut to size, and most people build a screen in 10–20 minutes using our step-by-step guide and assembly video. If you get stuck, contact us and we'll help.
Standard screens go up to 1795 mm on the longest side and are delivered Australia-wide. The shorter side can be up to 1450 mm, or up to 1750 mm in Midge mesh (the only mesh we stock in an 1800 mm roll). We can also make Extra Large screens up to 2500 mm on the longest side and 1750 mm on the shortest side. These are too long for our courier, so they are pickup only from our Miranda workshop and cost $15 extra. Screens over 1200 mm × 1200 mm need a mid rail.
A mid rail is recommended for larger screens and required for screens over 1200 mm × 1200 mm. Add one in the fly screen builder (horizontal or vertical). See how to install a mid rail.
Most Australian windows take the standard 11 mm frame. If the channel your screen sits in is narrower than 11 mm, as on many Bradnam's and A&L windows, order 9 mm. More on frame sizes.
We strongly recommend it. A spline roller is the tool that rolls the spline (a thin PVC cord) into the groove in the frame, locking the mesh in place. It makes assembly much smoother and stops you piercing the mesh. It's $4.99 and added to your order.
Your kit comes with the right spline. If you're buying spline separately, use 4 mm for 9 mm frames and for aluminium or stainless steel mesh, and 5.3 mm for everything else.
Yes. If your frame is in good condition, order fly screen mesh cut to size and spline, then follow our mesh fitting steps.
No. We specialise in made-to-measure window fly screens.
Yes. Choose pickup at checkout and collect from Unit 1/205–213 Port Hacking Road, Miranda NSW 2228, Monday to Friday, 9 am–5 pm. Come to the front door, press the Fly Screens In A Box buzzer, and bring your name and order number.
Yes. Order a mesh sample pack, a frame colour sample pack or both together. You can also try colours in our colour visualiser.
Yes. Fly screens keep out common flying insects such as flies, mosquitoes and moths. Very small insects can get through standard mesh, so choose midge mesh if midges or sandflies are a problem.
Take the screen out and wipe it with a damp cloth or sponge and mild soapy water. Avoid harsh chemicals and abrasive cleaners, which can damage the mesh.
We deliver DIY fly screen kits Australia-wide. Here's how our weekly production schedule works, so you know when to expect your order. Allow 2 weeks from order to delivery.
Every fly screen we send is made to order. We did the maths: between frame colours, mesh types, frame sizes, mid rails, fittings and sizes down to the millimetre, our fly screen builder allows 1,567,454,231,895,120 different combinations. That's more than 1.5 quadrillion, so every order takes time and precision to make sure you get exactly what you ordered.
As Australia heats up, so does demand for fly screens, and with more orders coming in, each one takes longer to get out the door. We know you want your fly screens as soon as possible, and we want you to have them as soon as possible too. But these aren't items we pick off a shelf. Everything is custom cut to your measurements, and there's real labour in every order. Thank you for your patience.
Next frame cut-off: Thursday 10 am (Sydney time)
Order before then to make this week's truck.
Your frames are cut on a computer-guided mitre saw for clean 45° corners, accurate to the millimetre.
Frames ordered before Thursday 10 am arrive at our Miranda workshop the following Monday.
We add your mesh, spline and accessories, check the order and pack your kit.
Your kit goes out by courier and you'll get tracking details by email.
| Order placed (Sydney time) | Frames cut on | Arrive in Miranda |
|---|---|---|
| Before Thursday 10 am | This week's run | The following Monday, then packed and dispatched |
| Thursday after 10 am to Sunday | Next week's run | The Monday after, then packed and dispatched |
Allow 2 weeks from order to delivery. Courier delivery usually takes 3–5 business days after dispatch. Remote areas can take a little longer.
Pay one shipping fee per order, whether you buy 1 screen or 10. Shipping is calculated at checkout.
The courier emails you tracking when your order ships. Not received it? Reply to your order email and we'll send it.
Choose pickup at checkout and collect from Fly Screens In A Box, Unit 1/205–213 Port Hacking Road, Miranda NSW 2228, Monday to Friday, 9 am–5 pm. Come to the front door, press the Fly Screens In A Box buzzer, and bring your name and order number.
Screens with a side over 1795 mm (up to 2500 × 1750 mm) are too long for our courier. If your order includes an Extra Large screen, Miranda pickup will be the only option at checkout.
Our fly screens are made to keep insects out and let fresh air in. It's important to understand what they're designed for, and how Australian building rules apply.
Standard fly screens are insect screens only. They can easily be pushed out and will not stop a child or adult falling through a window.
Under the National Construction Code, openable windows where the floor is 2 m or more above the ground outside (for example, many bedroom windows) need protection that stops the window opening more than 125 mm. A standard fly screen does not provide this. Use a compliant window restrictor, or a fall-prevention or security screen fitted by a professional.
If you live in a bushfire-prone area, your screens must comply with AS 3959, Construction of Buildings in Bushfire-Prone Areas, based on your property's BAL rating. Our 304 stainless steel bushfire mesh is rated to BAL-40 and suits bushfire-prone areas and mild to moderate coastal environments. It is not suitable for Flame Zone (BAL-FZ). Unsure of your rating? Ask your local council or fire authority before ordering. See which mesh suits each BAL.
| Area | Requirement | Responsibility |
|---|---|---|
| Fall prevention | High openable windows need a compliant restrictor or fall-prevention screen | Customer / installer |
| Bushfire safety | Mesh must suit your BAL rating. Ours is rated to BAL-40 (not BAL-FZ) | Customer chooses, we supply |
| Product use | Insect screen only, not a safety barrier | Customer |
| DIY fitting | Follow the guides provided | Customer |
We take great care to make every frame, mesh and accessory exactly to your order. If something goes wrong, we'll make it right as quickly as possible.
If your items don't match your order, were cut to the wrong size by us, or arrived damaged or faulty, contact us straight away for a replacement or refund. If your order is damaged in transit, we'll send a replacement at no cost.
If anything is missing from your kit (clips, mesh, spline and so on), let us know and we'll send it as soon as possible.
Every order is custom cut to your measurements, so we can't offer refunds or exchanges for incorrect measurements, the wrong frame size (9 mm or 11 mm), or the wrong mesh or colour. Unsure? Contact us before you order and we'll help you check.
Use our Contact Us page or email [email protected]. Include your order number and photos if you can, and we'll get back to you promptly.
| Issue | Covered? | What we do |
|---|---|---|
| Faulty, damaged or cut incorrectly by us | Yes | Full refund or replacement |
| Damaged in transit | Yes | Replacement sent straight away |
| Missing parts or accessories | Yes | Parts sent as soon as possible |
| Wrong size, mesh or colour ordered | No | Custom orders are non-refundable |
Read our full refund policy.
Made to measure, 23 frame colours, 5 mesh types, delivered Australia-wide.